胡状集油田胡5-15井区天然混合羧酸盐/黄胞胶驱油先导试验

报道了在室内实验研究中得到的混合天然羧酸盐/烷基磺基甜菜碱/黄胞胶复合驱油段塞结构:预冲洗段塞,10g/LKCl溶液;前置聚合物段塞,1500mg/L黄胞胶溶液;主驱油段塞,1.5×104mg/L混合天然羧酸盐+800mg/L烷基磺基甜菜碱DSB+800mg/L黄胞胶+5×103mg/L复碱(质量比1∶1的Na2CO3+NaHCO3)溶液;后置聚合物段塞,1000mg/L黄胞胶溶液。在岩心流动实验中0.3PV主段塞在水驱基础上提高采收率18.19%。胡状集油田胡5 15井区采出程度18.48%,油藏温度86℃,地层水矿化度1.7×105mg/L,Ca2+浓度4799mg/L,Mg2+浓度830mg/L,有油、水井各5口,综合含水已达96%(92%～99%)。从2000 01 24到2001 03 20,在5口注水井中依次注入预冲洗液2920m3,前置液2920m3,主驱油液49640m3(除一口井外均不加复碱),后置液2920m3,5口油井均见效,一些油井有效期超过20个月,油井产油量增加,含水下降,自然递减降低62.7%,采油速度升高0.46%。图3表2参3。     

PVDF中空纤维滤膜的形态结构

用Ｌ－Ｓ相转换法制备了聚偏氟乙烯（ＰＶＤＦ）中空纤维不对称滤膜。铸膜液由聚合物、溶剂和添加剂组成。用电子显微镜（ＳＥＭ）考察了聚合物浓度、添加剂用量及种类对膜形态结构的影响。实验结果表明，聚合物浓度对膜形态结构有显著影响，当铸膜液中聚合物浓度较低时，无论用什么种类添加剂，都能形成大、且多的孔，但孔的形状随添加剂不同而异。当恒定聚合物浓度时，添加剂的用量对膜形态结构有很大的影响，但孔的大小及多少与添加剂含量的多少不成正比。     

国外富过磷酸钙生产技术动态

本文介绍了国外富过磷酸钙生产技术的新进展。讨论了富过酸钙在我国的发展前景。     

一类广义耦合的KdV方程组的整体吸引子

利用Sobolev插值不等式和关于时间t的先验估计，研究了一类广义耦合的具有周期初值问题的KdV方程，得到了整体解和整体吸引子的存在性。     

糠醛注水——润滑油糠醛精制装置的节能途径

介绍了用水稀释糠醛使润滑油糠醛精制装置节能的途径。通过注水——糠醛－水溶液（含水９５％左右），可降低糠醛的气化沸点，增大换热系统的传热温差，改善换热效果，更多地回收能量，达到节约能源的目的。     

RADIATION FIELD FROM A RECTANGULAR PLAQUE SOURCE FOR RADIATION PROCESSING

Evaluation of the Hubbell integral for an omnidirectional detector response to a rectangular plaque gamma emitting radiation source using a different numerical computation method on a personal computer was made. For a plaque consisting of several strip gamma emitters, exposure rates at different positions above the source were calculated using 'exact' evaluation and an approximate method. Optimization method is used to find source activity of each strip, so as to acquire desirable dose uniformity of the irradiated products. In uses of the Hubbell integral, by introducing appropriate programming, computation time can be saved.     

Morphology and structure of poly(p-phenylene terephthalamide) crystallized from dilute organic solution

The high-temperature crystallization of poly(p-phenylene terephthalamide) (PPTA) from dilute organic solutions was achieved through the introduction of a non-solvent, or precipitating agent, at the desired crystallization temperature. The morphology and crystal structure were examined for crystals produced from PPTA polymer with two different molecular weights (M_w = 46000 and 3430 g mol⁻¹), using transmission electron microscopy. For the high-molecular-weight polymer, ribbon-like crystals were produced, while the low-molecular-weight polymer yielded small needles or platelets. In both cases, electron diffraction showed that the Northolt allomorph was obtained. For the high-molecular-weight polymer, the molecular axes were parallel to the ribbon axes in a chain-extended type structure. A hypothesis for the orientation of the low-molecular-weight PPTA in the small platelets, is also given.     

哈尔滨炼油厂MTBE装置试生产

介绍了哈尔滨炼油厂ＭＴＢＥ装置的工艺路线、新技术的应用及特点；催化剂的装填及应用情况；总结了生产过程中遇到的一系列问题及解决办法；探索了平稳生产的新徐径，以保证装置安全、平稳、长周期运行；同时对反应器操作温度、催化蒸馏塔操作压力、原料中醇烯比等因素对异丁烯转化率及ＭＴＢＥ产品的影响做了简单的总结。     

Measurements of Stress Intensity Factors of an Interface Crack Under Mixed Mode Loading

The optical method of caustics has been utilised to measure both the stress intensity factor for a crack lying along the interface of an aluminium/epoxy bimaterial specimen, and the mode mixity arising from the difference in the elastic properties across the interface. Measurements were carried out by using a novel modification to the method whereby caustics are produced and measured from both sides of the specimen, so compensating automatically for the distortion induced in the specimen due to misaligned loading fixtures. A flat reflective surface across the interface was obtained by adhering a reflective coating to the specimen. Verification that this coating does not affect measurement accuracy was obtained by comparing stress intensity factors measured from coated and uncoated monolithic aluminium specimens where good agreement was found to exist between both measurements.